Go Services

 

 

They are making a few good points related to A Step-by-Step Guide to Installing a Bathtub in general in this article down below.

Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough project. If the old tub is readily available, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the new one. Make certain you have actually qualified yourself for the task and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to think about utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your bathroom if you have actually currently purchased a brand-new bathtub and do not require to change the setup of your previous water system pipes.
Your devices as well as material list must comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing taps can be quite bothersome due to the limited access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin guaranteeing that the washing machines are in place in between the faucet and the sink. Protect the tap in position with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The former kind needs to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Mounting the Bathtub

Utilizing both wooden boards under its feet, put the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out degree.
To mount taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the same for the other tap.
Switch on the supply of water and check all joints and new pipework for leaks and tighten them if necessary. Load the bath tub and likewise check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bathtub needs to wait till the tub has been utilized at least once as this will certainly resolve it into its final position.

 

 

Planning for the Installment

Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now be ready to be suited its final placement.

 

 

Tiling Around the Bathtub

In the location where the bath satisfies the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to crack a stiff seal, causing the water to permeate the wall surface between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in use. The sealer can fracture fairly early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof adhesive and grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a devoted person who reads about Installing A Bathtub, I figured sharing that piece was a good idea. Loved our posting? Please share it. Let somebody else locate it. Many thanks for your time. Come back soon.

Book Your Appointment